Kathleen asked in a recent post what was on everyone’s design wall. Here is what is on mine:
Design Wall #1Design Wall #2
What is on yours? Post a link to your blog, (Flickr stream, FB page, Picasa, Shutterfly), etc in the comments or in the comments in Kathleen’s post. Let’s see your creativity in action.
Design Wall #1 annotated
Here is the explanation of what is going on on my ‘working’ design wall. It is working, because it is right in front of my sewing machine and I can grab things off of it.
We are midway through the foundation piecing class. This is a long tutorial, but there are a lot of steps and I want all of the parts to be clear. This would be a great tutorial for a video, but A) I don’t have a crew and B) I don’t do video.
This segment discusses more foundation piecing. In order to get to this point, you should have completed parts 1 and 2. All of the supplies are listed in Part 1
Remember our goal:
NY Compass Outline
Next, we need to foundation piece the small strip called Section D.
Cut fabric4 Pieces of fabric
Cut 4 pieces of fabric that coordinate with the fabrics of your block. The pieces should be about 2.5″x 1.75″, which is generous. You may be able to use scraps for these pieces. (Please ignore the messy cutting table)
Place fabric on pattern
As you did in Part 2, you will work on placing 2 fabrics on the line between D1 & D2 with about a quarter inch hanging over into D2 as a seam allowance. Note the printed part of the pattern (the lines on which you sew) are face down for this step.
Pin fabric
I like to pin the first piece of fabric to my pattern. It helps keep the fabric from shifting as I work on the second piece of fabric. Note the printed part of the pattern (the lines on which you sew) are face up for this step.
Position 2d piece of fabric
Flip Section D back over and position the second piece of fabric over the first.
Ready to Sew
When you have both of your pieces placed like you like them, pin in place. I like to use thin pins. Your piece should now look like the above photo.
Sew on lineSew on the line (#2)
With the applique’ foot on your machine. Sew on the line between D1 & D2. Do not cross the perpendicular line at the top or bottom. Back stitch one stitch at the beginning and the end.
Section D sewn
Once you have sewn on the line, your piece should look like the above photo.
Press first sewn pieces
Open up both pieces and make sure they cover D1 & D2. Once you are convinced that you have covered both D1 & D2 with your fabric and there is a 1/4″ seam allowance, press your piece. Press with the pattern on top. Note the pattern is face up and you can see the sewing lines. (Nota bene: if you have taped your pattern, use a press cloth so that you do not get melted tape on your iron)
Sewn, pressed Section D back
Flip your Section D over again, so you are ready to trim.
Ready to trim
Lay your pattern, with sewn fabric, pattern side up (fabric down) on your cutting mat. The inside part of the curve will be facing your body. You may want to flip Section D around if you are left handed.
Fold the longer piece of the pattern over to the left using the seam line as the fold line. This will expose the fabric that will be your seam allowance.
Place ruler on sewn line
Line up your ruler’s 1/4″ mark on the seam/fold line and trim your seam allowance to 1/4″.
TrimTrimmed
Trim seam allowance to 1/4″.
Ready to press pieces into place
Go back to the ironing board and position your piece so the fabric is up, pattern side down and smooth the fabric towards D2, lightly finger pressing.
Press towards D2Press towards D2
Take the piece to the iron and press carefully towards D2.
Place D3 fabric
Place your next fabric with the longer part towards D2 and the future seam allowance closer to D3. Hold the whole piece up to the light to make sure your placement is correct.
Place D3 fabric in place
Pin in place.
Get ready to sew on the line between D2 & D3.
Sewn D3
Once sewn, your piece should look like the photo above.
Check to make sure fabric covers D3
Check to make sure your fabric covers pattern section D3. You do this by folding the fabric over and looking to see that you have about 1/4″ on all sides.
Pattern side up
Now, get ready to trim. Put your piece on the cutting mat pattern side up.
Folder pattern back
Fold your pattern to the left again, like you did before.
Ready to trimTrimmed
Line up your ruler’s 1/4″ mark on the seam/fold line and trim your seam allowance to 1/4″.
Avoid the bump
See that bump in the photo above? You do not want that bump to show once you have pieced D4 on to the parts of Section D you have already pieced. Press again, this time towards D4. Avoid the bump by pressing!
Press towards D4
Press towards D4. No ironing!
We are heading to the home stretch!
Position D5
Position your last piece as you have done before. It is going to look at little weird and out of alignment, because you are working with a curve. Remember to position the fabric so it covers D5 plus 1/4″ seam allowance. Pay no attention to the edges of the other pieces, such as D4, that you have already sewn.
Check placement
It is easier for me to see whether or not piece D5 was in the right position by pinning it. Note, I would pin it on the pattern side to sew, because then I can see where the pin is in relation to where my sewing machine foot and needle are. the pin in the photo is temporary.
Sewn D5
Once you have the placement finalized, go ahead and sew.
Fold back pattern and prepare to trim seam allowanceAlign ruler for 1/4″ seam allowance
Now you have to fold back the pattern one last time and prepare to trim the seam allowance.
D5 trimmed!
Trim!
Section D Complete!
Now your piece is done. Fold back the D5 fabric and press. Place your ruler on the lines at the end of the pattern and trim a 1/4″ seam allowance. I know you can do this without photos.
Now you have to trim the curved parts of Section D
Untrimmed Section D
It is too difficult to sew the untrimmed Section D, so you will have to trim.
Dots mark 1/4″
To trim, mark 1/4″ away from the dark line. The dots in the photo above mark 1/4″. I have trimmed the straight ends with a rotary cutter and I am ready to play “dot to dot” with my scissors. I am going to cut from dot to dot to create a 1/4″ seam allowance.