Sampler Class: Fusible Machine Applique’ Tutorial Part 2

We are making the Flower Wreath block. To find out how to make templates, including the ring see Part 1.

Flower Wreath
Flower Wreath

Choose your fabrics. You will need fabric for the flowers (1-4 fabrics), leaves (1-20 fabrics) and the wreath (1 fabric). The leaves can be the traditional green or you can use something else. If you use one color, you might want to mix up the prints to increase interest. You can also use different colors. Make the block your own.

I am going to try and use a variety of turquoises and aquas to keep my color scheme in the aqua/turquoise with red range. I have a few of the leaf fabrics picked out from my scrap basket, but need to find more. It is important, with my limited color scheme to make sure the viewer can see the individual leaves.

Cut piece large enough for ring
Cut piece large enough for ring

The ring is the biggest pain to deal with so I deal with it first before I even really think much about fabrics for the other parts. I decided to use one of the Pat Bravo Pure Elements solids in the turquoise range, but more on the green side. I haven’t used it in this quilt before. I picked it to highlight the leaves a little more.

Cover fabric with fusible
Cover fabric with fusible

Now you need to make sure that your fusible will cover your fabric.

I used a package of Steam-a-Seam 2 Lite, but there are many fusibles that will work just fine for this project. Use what you know how to use or what you have on hand.

Tear the paper carefully off of one side of the fusible (or follow directions for your fusible) and stick it to the fabric, smoothing it carefully so there are no puckers or bubbles. The fusible is sticky so you can stick to the fabric and reposition it until you are happy.

Back of fusible backed fabric
Back of fusible backed fabric

Since the pieces I had were 8.5″x11″, I needed to cover an extra piece (bottom of the photo above) that was wider than the 8.5″ width of the fusible. I cut a piece from the fusible (white part in photo above) and re-positioned it  to cover the part of the fabric I need for the size of the template.

Once you are happy, fuse the 2 sided fusible (should have the paper left on one side) to your ring fabric. Follow the directions on the package or website. You may want to cover your ironing board and the piece with junk fabric or an applique’ pressing sheet to keep your iron and ironing surface clean.

Turn your fusible backed fabric so that the paper left on the fabric is face up, as in the photo above. Place your ring template face down on the paper and trace around it with a pencil.

Ring cut out
Ring cut out

Cut out the ring carefully on the line. I used an X-acto knife to start the center. I did use a pair of fabric scissors, but not my Gingher scissors. It is kind of hard to know what to do, because you are cutting both fabric and paper and you need a nice sharp edge. I use a pair of my mid-range scissors and hope for the best. They still seem sharp even after a bit of this type of cutting.

Fold the ring into quarters and finger press lightly. Again you will be lining up the folds to center the ring.

Retrieve your background. Fold the background into quarters and finger press, so you can see the folds.

Line up ring on background
Line up ring on background

 

Remove paper from the ring.

Line up the folds of the ring on the folds of the background. If they are all in alignment, there should be a ring fold snuggled with a background fold evenly. If you want to check, measure from the edge to the ring. You do need an absolutely square block for this to work.

Press the ring onto the background so it sticks.

Carefully bring background with the ring stuck to it to the iron. Check to see that your ring is still in place. According to your fusible directions, press the ring into place.

Your ring should now be firmly ironed on to the center of the background.

Leave this piece on the ironing board temporarily.

Get the tearaway you purchased (or had) and cut two pieces of tearaway stabilizer a little bit larger than your background. Place your background on top of the tearaway and pin it to the background. This will provide stability and prevent the piece from puckering when you zig zag stitch the pieces.

You are now ready to machine applique’ your first part of the block. See part 3 for machine stitching the block.

Author: Jaye

Quiltmaker who enjoys writing and frozen chocolate covered bananas.